$128.99 Buy It Now or Best Offer
free,30-Day Returns

Seller Store
() %,

Location: Ontario, California, United States
Ships to: US,
Item: 314000304742

eBay 1.Fit For Nissan Frontier 1999-2004 3.3L 6 Cylinder Only Nissan Xterra 2000-2004 2.Package Includes: 1x Part# Front Lower Left Control Arm + Pre-Assembled Ball Joint (Driver) – K620556 1x Part# Front Lower Right Control Arm + Pre-Assembled Ball Joint (Passenger) – K620557 2x Part# Front Outer Tie Rods Ends Links – ES3661 2x Part# Front Inner Tie Rods Ends Links – ES3660 Notes For 1999-2004 Nissan Frontier 6pcs Front Lower Control Arms Tie Rod Links Kit 1.Fit For Nissan Frontier 1999-2004 3.3L 6 Cylinder Only Nissan Xterra 2000-2004 2.Package Includes: 1x Part# Front Lower Left Control Arm + Pre-Assembled Ball Joint (Driver) – K620556 1x Part# Front Lower Right Control Arm + Pre-Assembled Ball Joint (Passenger) – K620557 2x Part# Front Outer Tie Rods Ends Links – ES3661 2x Part# Front Inner Tie Rods Ends Links – ES3660 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Items Included : Mounting Hardware Custom Bundle : Yes Interchange Part Number : ES3466 ES3660 K620556 K620557 OE/OEM Part Number : Suspension Control Arms and Ball Joints Assembly,Tie Rod End Superseded Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : topcn-autoparts Manufacturer Part Number : TA81415301P Adjustable : Yes Modified Item : Yes Kit Parts Included : Control Arm,Ball Joint Kit or Single Part : Kit Greasable or Sealed : Greasable OE Spec or Performance/Custom : OE Spec Surface Finish : Polished, Rust Protected Quantity : 6 Pcs Kit Parts Included : Control Arm,Tie Rod End Cross Reference Part Number : 545019Z510,545019Z510,485200P725,485200P726 Cross Reference Part Number : 485203S525,485204P025.48520OW025,485703S535 Cross Reference Part Number : D8510VK90A,D85200W025,D8520OW025,D8520VK90A,485703S525 Features : Greasable Finish : Coated Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On Discount Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales 2x Front Hood Gas Lift Supports Struts Shocks Springs For Dodge Ram 02-10 4364 USD 16.81 2x Front Hood Lift Supports Shocks Struts For Dodge Ram 1500 2500 3500 4500 5500 USD 17.54 Throttle Body for Dodge Avenger Journey Caliber Jeep Patriot Compass 2.4L 2.0L USD 43.99 Upstream & Downstream Oxygen O2 02 Sensor For 2001-2005 Honda Civic 1.7L D17A7 USD 23.81 2 For Dodge Challenger 2008-2014 Keyless Entry Remote Control Car Key Fob USD 17.95 Newly Listed Timing Chain Kit Water Oil Pump For Nissan Maxima Quest Altima USD 108.55 2PCS Mirrors Complete Pairs Black For 2002-2018 International Durastar 4200 4300 USD 280.99 For 1980-96 Ford Bronco Pickup Truck Manual Black Steel 5×8’Swing Lock Mirror USD 26.43 For ACURA TL 2004 – 2008 Front And Rear Brake Rotors Ceramic Pad Drilled Slotted USD 170.69 Alloy For 17-22 GMC Acadia Genuine GM Package 84456361 Roof Rack Rail Cross Bar USD 83.09 Terms & Contact Shipping Policy Payment Policy Return Policy FAQ About Us For 1999-2004 Nissan Frontier 6pcs Front Lower Control Arms Tie Rod Links Kit 1.Fit For Nissan Frontier 1999-2004 3.3L 6 Cylinder Only Nissan Xterra 2000-2004 2.Package Includes: 1x Part# Front Lower Left Control Arm + Pre-Assembled Ball Joint (Driver) – K620556 1x Part# Front Lower Right Control Arm + Pre-Assembled Ball Joint (Passenger) – K620557 2x Part# Front Outer Tie Rods Ends Links – ES3661 2x Part# Front Inner Tie Rods Ends Links – ES3660 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Items Included : Mounting Hardware Custom Bundle : Yes Interchange Part Number : ES3466 ES3660 K620556 K620557 OE/OEM Part Number : Suspension Control Arms and Ball Joints Assembly,Tie Rod End Superseded Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : topcn-autoparts Manufacturer Part Number : TA81415301P Adjustable : Yes Modified Item : Yes Kit Parts Included : Control Arm,Ball Joint Kit or Single Part : Kit Greasable or Sealed : Greasable OE Spec or Performance/Custom : OE Spec Surface Finish : Polished, Rust Protected Quantity : 6 Pcs Kit Parts Included : Control Arm,Tie Rod End Cross Reference Part Number : 545019Z510,545019Z510,485200P725,485200P726 Cross Reference Part Number : 485203S525,485204P025.48520OW025,485703S535 Cross Reference Part Number : D8510VK90A,D85200W025,D8520OW025,D8520VK90A,485703S525 Features : Greasable Finish : Coated Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On DiscountShippingWarrantyReturnFeedback Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of Topcn-autoparts. All rights reserved.

Frequently Asked Questions About For 1999-2004 Nissan Frontier 6pcs Front Lower Control Arms Tie Rod Links Kit in My Website

medtopis.com is the best online shopping platform where you can buy For 1999-2004 Nissan Frontier 6pcs Front Lower Control Arms Tie Rod Links Kit from renowned brand(s). medtopis.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling For 1999-2004 Nissan Frontier 6pcs Front Lower Control Arms Tie Rod Links Kit on medtopis.com?

medtopis.com helps you to shop online and delivers Michael Kors to your doorstep. The best-selling Michael Kors on medtopis.com are: Michael Kors Sullivan Large IPad Laptop Travel Leather Bag Tote Soft Pink Nwt NWT Michael Kors Women’s Sandrine Stud Small Leather Crossbody Vanilla/Acorn Michael Kors Greenwich Medium Saffiano Tote Watermelon Luggage *Non Outlet* Michael Kors Soho Quilted Leather Shoulder Handbag Michael Kors dune carry all leather purse Michael Kors Clutch/Wristlet With Removable Pouch Black/Grey Excellent Used Cond Michael Kors Cream Tan & White MK Logo Crossbody -3 compartments Michael Kors Jet Set LargeMessenger + LG Flat MF Phonecase + dust bag (black) Michael Kors large wallet envelope logo embossed light cream Michael Kors White/Gray Full Zip Wallet & Belt NEW! Michael Kors Jet Set Grommet Vanilla Leather Large Zip Clutch 10″x5.5″ Michael kors Handbag MK Red Crossbody Leather Large Messenger Shoulder Bag Purse Michael Kors Sheila Small Center Zip Satchel Handbag+Top Zip Coinpouch (Oxblood) Michael Kors Medium Double Pocket Tote Handbag Bag Purse + Long Wallet Wristlet Michael Michael Kors Kaylee Medium Leather 1pc Satchel Black NWD MICHAEL KORS JET SET BROWN TOTE BAG *NWT* MICHAEL KORS MEDIUM CROSSBODY FASHION LEATHER BAG HANDBAG PURSE SHOULDER RED MK Michael Kors Junie Leather Shoulder Medium Handbag NWT Michael Kors Cranberry Red Saffiano Leather Savannah Purse Satchel Michael Kors Ludlow Large Shoulder Bag – Excellent Condition Michael Kors Hamilton Handbag Michael Kors MINI Avril XS Cheetah Leather Satchel Crossbody Bag Cream Multi Michael Kors Tan Leather Crossbody Michael Kors handbag black Crossbody With Gold Chain Strap michael kors jet set saffiano tote large MICHAEL Kors black leather purse Michael Kors Handbag $49.99 michael kors handbag used Michael Kors Voyager Embossed Patent Leather Logo Tote Shoulder Bag Heather Grey MICHAEL KORS WOMENS MEDIUM ZIP POCKET TRAVEL SHOULDER BACKPACK BAG BRIGHT RED MICHAEL KORS Women’s Soft Quilted Elegant Leather Tech Size М preowned used michael kors purse NWT MICHAEL KORS KARSON CARRYALL LG SIGNATURE DARK DUNE TOTE MSRP: $278 michael kors purse used Michael Kors Jet Set Multifunction Pocket Tote Bag Brown Retail $178 Michael Kors Black Tote Michael Kors Ava XS Saffiano Leather Crossbody – Soft Pink Uh-mazing purple woven patent Michael Kors clutch B-0903 MICHAEL Michael Kors Hamilton Traveler Messenger Bag in Gooseberry Green $298 Michael Kors Hamilton Whipped Shoulder bag Luggage Leather NEW $248.00 Used michael kors crossbody-Cream color, barely used  Michael Kors Women’s MK4336 Sofie Analog Display Quartz Rose Gold Watch Michael Kors handbag medium Darkest brown & tan only used a few times   michael kors handbag used buy it now Michael Kors Carmen SM Flap Satchel michael kors black handbag used Michael Kors Emmy Flower Pop Backpack Perfect! Michael Michael Kors Blue Leather Ring Tassel Tote Michael Kors Gold Leather Hobo Bag MICHAEL KORS PURSE USED [Michael Kors] BEDFORD LEGACY XS DUFFLE XBODY 32F9G06C0B 252 BROWN×ACORN Michael Kors Jet Set Travel Beige Saffiano Leather Double Handle Zipper Tote Bag Michael Kors Jet Set Large EW Brown Signature PVC Zip Chain Crossbody Bag Purse Michael Kors Loafers AUTHENTIC MICHAEL KORS JET SET WALLET ON LEATHER WRISTBAND /SHOULDER CROSSBODY Michael Kors Crossbody in camel brown leather Authentic Michael Kors travel tote new with tags yellow, tan and White color Genuine MICHAEL KORS Bedford Legacy yellow pebbled leather chain link bag michael kors handbag used MICHAEL Michael Kors Women Leather Clutch One Size Michael Kors Hand Bag 1974222 USA. D9 Michael Kors cross body purse MICHAEL KORS Navy Blue Leather Gold Pyramid Studded Wristlet michael kors saffiano tote NAVY Michael Kors Large Studded Hamilton Satchel Bag Michael Kors Walsh Medium Vanilla/Brown Logo Tote NEW Michael Kors Pink Tote Michael Kors McKenna Medium Satchel in Brown Pebbled Leather $498 MICHAEL KORS Brown Leather Gold Chain LARGE Purse Handbag DUSTBAG INCL NWB Michael Kors Rose Quilted Convertible Belt White 35T0SXOC1I $348 Gift Bag FS Michael Kors Jet Set Charm Wristlet – Medium Top Zip Luggage Brown Leather NWT Michael Kors Large Crossbody Messenger Purse (10in x 10in) Neutral Light Grey MICHAEL Michael Kors XL Jet Set Chain Shoulder Brown Tote Michael Kors Scarf White And Black Michael Kors Tan Jet Set Shoulder Purse MICHAEL KORS Anabelle Large Leather Tote-Pale Pink michael kors handbag soft Leather brass lots of pockets Michael Kors beige purse Michael Kors Ankle Boots Size 6 – Botas de Tobillo Michael Kors Michael Kors Slate Estra Small Animal Print Calf Hair And Leather Blacl/brwn Michael Kors Medium Coated Canvas Signature MK Logo Travel Kit Case (Pale Gold) Michael Kors Sheila Crossbody Michael Kors Camel Leather Purse Michael Kors Jet Set Travel Large East West Travel Tote, Brown michael kors handbag Woman’s Handbags MICHAEL Michael Kors Jet Set Large East/West Crossbody Michael Kors Black Pebbled Leather Two Zipper Double Pockets Shoulder Handbag Michael Kors – “Maxine” In Brown / Acorn – Medium- Retail $298 New Michael Kors Saffiano Tan Purse MICHAEL KORS Large Black Leather Studded Twisted Buckles Convertible Tote Michael Kors Jet Set Travel Medium Carryall Tote – Grey MICHAEL Michael Kors Top Zip Crossbody Black (Pre-owned/as pictured) Michael Kors belt bag in white and grey MICHAEL KORS Jet Set Item Tan Brown Logo Print Zip Clutch Wristlet MICHAEL Michael Kors-Black w/ Gold Hardware Oversized Clutch w/ removable straps MICHAEL KORS Brown Khaki HANDBAG Tote Michael Kors Watermelon Jet Set Leather Crossbody Michael Kors Sandrine Studded Large Zip Clutch Ballet Final Sale NWT Michael Kors Quilted Jet Set Crossbody MICHAEL MICHAEL KORS Edith Large Satchel Rubin Red New With Defects Mens Pullover Fleece Hoodie